CITROEN RELAY TACHOGRAPH FITTING INSTRUCTIONS, MANUAL FWD, 2005 ON

http://servuclean.com/username CITROEN RELAY TACHOGRAPH FITTING INSTRUCTIONS, MANUAL FWD, 2005 ON

best site to buy provigil online CITROEN RELAY TACHOGRAPH FITTING INSTRUCTIONS, MANUAL FWD, 2005 ON

As from 1st October 2012 According to Regulation (EU) No 1266/2009 (Annex1b) it is a legal requirement that an independent motion signal is connected to an activated DTCO, Therefore for this digital installation a DTCO Geoloc is required part number A2C59514979.

TACHOGRAPH KIT PART NUMBER: 13810518

VEHICLE MANUFACTURER: Citroen

MODEL: Relay

TRANSMISSION: Manual FWD

YEAR: 2006 on

ENGINE: Diesel

VOLTAGE: 12v

FITTING INSTRUCTIONS

Remove original speed sensor if fitted, if not installed remove the plastic blanking plug which is found on the top of the diff and with the Fiat/Citroen/Peugeot parts install the KITAS sender unit.

* These parts are not included in the kit

CITROEN RELAY TACHOGRAPH FITTING INSTRUCTIONS, MANUAL FWD, 2005 ON

CITROEN RELAY TACHOGRAPH FITTING INSTRUCTIONS, MANUAL FWD, 2005 ON

CITROEN RELAY TACHOGRAPH FITTING INSTRUCTIONS, MANUAL FWD, 2005 ON

For vehicles that have the existing speed sensor the speed signal from pin 3 of the original speed sensor grey/green must be connected to B6 at the rear of the DTCO. Another installation option is to remove the top part of the centre consol and install the DTCOas shown below using a X39-140-000-011(installation housing ) and 132402011 (facia).

CITROEN RELAY TACHOGRAPH FITTING INSTRUCTIONS, MANUAL RWD, 2005 ON
CITROEN RELAY TACHOGRAPH FITTING INSTRUCTIONS, MANUAL RWD, 2005 ON

Fitting Kit 13810518consists of:-

QUANTITY PART DESCRIPTION PART NUMBER

1 DTCO TACHOGRAPH 1381-0050209001

1 PLUG & HARNESS 1318-90100000

1 SENDER UNIT 2171-01000010

1 SENDER CABLE 21700421

1 DTCO MOUNTING SLEEVE 1324-90010500

1 DTCO REAR SEALING COVER 1381-90020100

1 DTCO REAR SEALING COVER SCREW HS07-0100-116

1 DTCO OPERATING INSTRUCTIONS BA00-1381-20101102

 

CABLE COLOUR              DESCRIPTION           DTCO PIN CONNECTION

WHITE                            INGINTION                         A3

BLACK                             GROUND                          A5

RED                                SUPPLY (9-36V)                A1

 

Installation of Geoloc:

Installation instructions

In order to provent GPS sensitivity issues, the module needs to be installed in a position where the module has a clear view to sky and satellites.

1-  When installing the geoloc module in a vehicle, make sure that there are as few obstruction as possible close to the unit since it has an internal GPS antenna. Any obstruction might block the 360 view to the horizon that is required for operation. Ideally, nothing should block the antenna beyond 5 degrees above the horizon with the best location being on the windscreen.

2-  The GPS receiver antenna (Patch-Antenna) is located underneath the type data plate. Therefore the data plate (antenna side of the module) should face upwards towards the sky

PLEASE NOTE: The Geoloc is equipped with 120 Ohm can resistor. The wiring to CAN 1 or CAN 2 must take this into account!

Whilst every effort is made to ensure the accuracy of the information given here, TACHO SUPPLIES Ltd cannot be held responsible for any errors or omissions. Ultimately, the installer must ensure compliance with the specific vehicle repair procedures laid down by the vehicle manufacturer; particularly with regard to battery disconnection/reconnection procedures. Failure to comply with the vehicle manufacturer’s instructions may result in personal injury and/or component damage/memory loss.