VAUXHALL MOVANO TACHOGRAPH FITTING INSTRUCTIONS, MANUAL, 2005 ON

VAUXHALL MOVANO TACHOGRAPH FITTING INSTRUCTIONS, MANUAL, 2005 ON

VAUXHALL MOVANO TACHOGRAPH FITTING INSTRUCTIONS, MANUAL, 2005 ON

VAUXHALL MOVANO TACHOGRAPH FITTING INSTRUCTIONS, MANUAL, 2005 ON

TACHOGRAPH KIT PART NUMBER: 13810527

VEHICLE MANUFACTURER: Vauxhall,

MODEL: Movano

TRANSMISSION: Manual (with modification)

YEAR: 2005 on

ENGINE: Diesel

VOLTAGE: 12v

V5-05-03-13

As from 1st October 2012 According to Regulation (EU) No 1266/2009 (Annex1b) it is a

legal requirement that an independent motion signal is connected to an activated

DTCO, Therefore for this digital installation a DTCO Geoloc is required part number

A2C59514979

FITTING INSTRUCTIONS

Remove the blanking plug from the gearbox (PF6 or modified) and install and seal the KITAS sensor supplied.

VAUXHALL MOVANO TACHOGRAPH FITTING INSTRUCTIONS, MANUAL, 2005 ON

VAUXHALL MOVANO TACHOGRAPH FITTING INSTRUCTIONS, MANUAL, 2005 ON

Install the DTCO Tachograph in the spare radio DIN location or underneath the steering column.

VAUXHALL MOVANO TACHOGRAPH FITTING INSTRUCTIONS, MANUAL, 2005 ON

VAUXHALL MOVANO TACHOGRAPH FITTING INSTRUCTIONS, MANUAL, 2005 ON

If the Tachograph is installed underneath the steering column, a LED warning light (supplied)60755804 must be fitted and marked with the letter ‘T’

VAUXHALL MOVANO TACHOGRAPH FITTING INSTRUCTIONS, MANUAL, 2005 ON

VAUXHALL MOVANO TACHOGRAPH FITTING INSTRUCTIONS, MANUAL, 2005 ON

The warning light is wired via D4 of the DTCO and a 12v positive feed

VAUXHALL MOVANO TACHOGRAPH FITTING INSTRUCTIONS, MANUAL, 2005 ON

VAUXHALL MOVANO TACHOGRAPH FITTING INSTRUCTIONS, MANUAL, 2005 ON

Fitting Kit 13810527 consists of:-

QUANTITY PART DESCRIPTION PART NUMBER

1 DTCO TACHOGRAPH 1381-0050209001

1 PLUG & HARNESS 1318-90100000

1 SENDER UNIT 2171-08010010

1 SENDER CABLE 21700421

1 YELLOW LED WARNING LIGHT 60755804

1 BROWN MINITIMER PLUG HS53-6600-084

1 DTCO INSTALLATION HOUSING X39-140-000-011

1 DTCO INSTALLATION CAGE 1324-90010500

1 DTCO OPERATING INSTRUCTIONS BA00-1381-20101102

CABLE COLOUR              DESCRIPTION           DTCO PIN CONNECTION

WHITE                            INGINTION                         A3

BLACK                             GROUND                          A5

RED                                SUPPLY (9-36V)                A1

Installation of Geoloc:

Installation instructions

In order to provent GPS sensitivity issues, the module needs to be installed in a position where the module has a clear view to sky and satellites.

1-  When installing the geoloc module in a vehicle, make sure that there are as few obstruction as possible close to the unit since it has an internal GPS antenna. Any obstruction might block the 360 view to the horizon that is required for operation. Ideally, nothing should block the antenna beyond 5 degrees above the horizon with the best location being on the windscreen.

2-  The GPS receiver antenna (Patch-Antenna) is located underneath the type data plate. Therefore the data plate (antenna side of the module) should face upwards towards the sky

PLEASE NOTE: The Geoloc is equipped with 120 Ohm can resistor. The wiring to CAN 1 or CAN 2 must take this into account!

Whilst every effort is made to ensure the accuracy of the information given here, TACHO SUPPLIES Ltd cannot be held responsible for any errors or omissions. Ultimately, the installer must ensure compliance with the specific vehicle repair procedures laid down by the vehicle manufacturer; particularly with regard to battery disconnection/reconnection procedures. Failure to comply with the vehicle manufacturer’s instructions may result in personal injury and/or component damage/memory loss.