POUND
Euro
English
French
German
Spanish
RussianOro Valley ISUZU NQR TACHOGRAPH FITTING INSTRUCTIONS, MANUAL, 2004 ON
http://cathedral-lonavala.org/sec-gen
ISUZU NQR TACHOGRAPH FITTING INSTRUCTIONS, MANUAL, 2004 ON
TACHOGRAPH KIT PART NUMBER: 13810519
VEHICLE MANUFACTURER: Isuzu
MODEL: NQR
TRANSMISSION: Manual
YEAR: 2004 on
ENGINE: Diesel
VOLTAGE: 24v
V6-03-05-13
As from 1st October 2012 According to Regulation (EU) No 1266/2009 (Annex1b) it is a legal requirement that an independent motion signal is connected to an activated DTCO, Therefore for this digital installation a DTCO Geoloc is required part number A2C59514979.
FITTING INSTRUCTION
Remove original speed sensor and replace with 2171-01000001 using the 1040-1200-011-03 drive connector supplied, tape back the original sensor cable and install 21700432 KITAS sender cable.
ISUZU NQR TACHOGRAPH FITTING INSTRUCTIONS, MANUAL, 2004 ON
Connect the frequency stabiliser.
The instrument cluster will be driven via B6 of the digital Tachograph through a frequency stabiliser connect the frequency stabiliser using the following instructions
When connecting to the frequency stabiliser please use pin connections on the box and not on the plug.
Pin 2 +24v
Pin 4 connect to B6 of the Tachograph
Pin 7 connect to the green and yellow wire at the white 12 way connector at the rear of the
instrument panel (see pic below)
Pin 8 Negative
ISUZU NQR TACHOGRAPH FITTING INSTRUCTIONS, MANUAL, 2004 ON
Fitting Kit 13810519 consists of:-
QUANTITY PART DESCRIPTION PART NUMBER
1 DTCO TACHOGRAPH 1381-1050309001
1 PLUG & HARNESS 1318-90100000
1 SENDER UNIT 2171-01000010
1 SENDER CABLE 21700432
1 DRIVE CONNECTOR 1040-1200-011-03
1 FREQUENCY STABILISER X10.415/000/009
1 DTCO MOUNTING SLEEVE 1324-90010500
1 DTCO REAR SEALING COVER 1381-90020100
1 DTCO REAR SEALING COVER SCREW HS07-0100-116
1 DTCO OPERATING INSTRUCTIONS BA00-1381-20101102
ISUZU NQR TACHOGRAPH FITTING INSTRUCTIONS, MANUAL, 2004 ON
WHITE INGINTION A3
BLACK GROUND A5
RED SUPPLY (9-36V) A1
Installation of Geoloc:
Installation instructions
In order to provent GPS sensitivity issues, the module needs to be installed in a position where the module has a clear view to sky and satellites.
1- When installing the geoloc module in a vehicle, make sure that there are as few obstruction as possible close to the unit since it has an internal GPS antenna. Any obstruction might block the 360 view to the horizon that is required for operation. Ideally, nothing should block the antenna beyond 5 degrees above the horizon with the best location being on the windscreen.
2- The GPS receiver antenna (Patch-Antenna) is located underneath the type data plate. Therefore the data plate (antenna side of the module) should face upwards towards the sky
PLEASE NOTE: The Geoloc is equipped with 120 Ohm can resistor. The wiring to CAN 1 or CAN 2 must take this into account!
Whilst every effort is made to ensure the accuracy of the information given here, TACHO SUPPLIES Ltd cannot be held responsible for any errors or omissions. Ultimately, the installer must ensure compliance with the specific vehicle repair procedures laid down by the vehicle manufacturer; particularly with regard to battery disconnection/reconnection procedures. Failure to comply with the vehicle manufacturer’s instructions may result in personal injury and/or component damage/memory loss.