FORD TRANSIT TACHOGRAPH FITTING INSTRUCTIONS, MANUAL, REAR WHEEL DRIVE, AUG 2005 ON

 

FORD TRANSIT TACHOGRAPH FITTING INSTRUCTIONS, MANUAL, REAR WHEEL DRIVE, AUG 2005 ON

FORD TRANSIT TACHOGRAPH FITTING INSTRUCTIONS, MANUAL, REAR WHEEL DRIVE, AUG 2005 ON

 

FORD TRANSIT TACHOGRAPH FITTING INSTRUCTIONS, MANUAL, REAR WHEEL DRIVE, AUG 2005 ON

Manual (Rear wheel drive) 6 speed

2.4Ltr. Diesel

2005 onwards

12v

As from 1st October 2012 According to Regulation (EU) No 1266/2009 (Annex1b) it is a legal requirement that an independent motion signal is connected to an activated DTCO, Therefore for this digital installation a DTCO Geoloc is required part number A2C59514979.

CABLE COLOUR              DESCRIPTION           DTCO PIN CONNECTION

WHITE                            INGINTION                         A3

BLACK                             GROUND                          A5

RED                                SUPPLY (9-36V)                A1

FITTING INSTRUCTIONS

1. Remove the 18mm-blanking plug from the R/H. Check the fit of the Bezel and Cover before drilling the 4 x 3mm Bezel retaining screw holes and securing the Bezel.

8. Wire-up the Plug and Harness (supplied) and route this and the Sender Unit cable through the 32mm

9. Hole to the tachograph location and fit the grommet (supplied) in the hole.

10. Insert the Installation Trim in the right-hand hole in

Figure 2

FORD TRANSIT TACHOGRAPH FITTING INSTRUCTIONS, MANUAL, REAR WHEEL DRIVE, AUG 2005 ON

FORD TRANSIT TACHOGRAPH FITTING INSTRUCTIONS, MANUAL, REAR WHEEL DRIVE, AUG 2005 ON

11. Fit the KITAS Sender Unit (supplied) in place of the blanking plug and securely tighten. Fig 1

12.   Connect the Sender Unit Cable (supplied) to the KITAS Sender Unit and route the cable to the centre of the underside of the dashboard.

13.   Remove the 2 screws retaining the Centre Cover on top of the dashboard and lift the Centre Cover off (see fig. 1 up to 05)

14.  Lift out the left-hand electrical compartment tray on top of the dashboard to gauge available depth behind dashboard BEFORE drilling any holes.

FITTING KIT 13810502 CONSISTS OF:-

QUANTITY PART DESCRIPTION PART NUMBER

1 DTCO TACHOGRAPH 1381-0050209001

1 SENDER UNIT 2171-20302410

1 SENDER CABLE 21700421

1 PLUG AND HARNESS 1318-90100000

1 INSTALLATION TRIM 1324-90010500

1 DTCO REAR SEALING COVER 1381-90020100

1 DTCO REAR SEALING COVER SCREW HS07-0100-116

1 DTCO OPREATING INSTRUCTIONS BA00-1381-20101102

Installation of Geoloc:

Installation instructions

In order to provent GPS sensitivity issues, the module needs to be installed in a position where the module has a clear view to sky and satellites.

1-  When installing the geoloc module in a vehicle, make sure that there are as few obstruction as possible close to the unit since it has an internal GPS antenna. Any obstruction might block the 360 view to the horizon that is required for operation. Ideally, nothing should block the antenna beyond 5 degrees above the horizon with the best location being on the windscreen.

2-  The GPS receiver antenna (Patch-Antenna) is located underneath the type data plate. Therefore the data plate (antenna side of the module) should face upwards towards the sky

PLEASE NOTE: The Geoloc is equipped with 120 Ohm can resistor. The wiring to CAN 1 or CAN 2 must take this into account!

Whilst every effort is made to ensure the accuracy of the information given here, TACHO SUPPLIES Ltd cannot be held responsible for any errors or omissions. Ultimately, the installer must ensure compliance with the specific vehicle repair procedures laid down by the vehicle manufacturer; particularly with regard to battery disconnection/reconnection procedures. Failure to comply with the vehicle manufacturer’s instructions may result in personal injury and/or component damage/memory loss.