MITSUBISHI L200 TACHOGRAPH FITTING INSTRUCTIONS

buy stromectol online in u.k MITSUBISHI L200 TACHOGRAPH FITTING INSTRUCTIONS

Mount Lebanon MITZUBUSHI TACHOGRAPHS

MITZUBUSHI TACHOGRAPH

MANUAL & AUTOMATIC 2006 ON 12V

MITSUBISHI L200 TACHOGRAPH FITTING INSTRUCTIONS

MITSUBISHI L200 TACHOGRAPH FITTING INSTRUCTIONS

FITTING INSTRUCTIONS

Remove original speed sensor and replace with 2171-01000010 using the 1040-1200-011-03 drive connector supplied, tape back original sensor and install 21700432 KITAS sender cable

MITSUBISHI L200 TACHOGRAPH FITTING

MITSUBISHI L200 TACHOGRAPH FITTING

Drill 2mm hole for sealing the sender unit to the gearbox

 CONNECTING THE FREQUENCY STABILISER

The instrument cluster will be driven via B6 of the digital tachograph through a frequency stabiliser connect the frequency stabiliser using the following instruction

WHEN CONNECTING TO FREQUENCY STABILISER PLEASE USE PIN CONNECTIONS ON THE BOX AND NOT ON THE PLUG

Pin 2 + 12v

Pin 4 connect toB6 of the tachograph

Pin 7 connect to the black and yellow wire found on the white plug at 26 and for the mitsubishi connect to the white and blue wire on the passanger side foot well

see picture below or behind the instrument panel, white 12 pin connector (middle one) position 2 white/blue. For the kia sorento connect to black/blue wire at the gearbox

Pin 8 negative

MITSUBISHI TACHOGRAPH FITTING

MITSUBISHI TACHOGRAPH FITTING INSTRUCTIONS

 ISUZU TACHOGRAPH FITTING LOCATION

The DTCO ca be installed using the double din panel that can be obtained from isuzu

ISUZU part number 8-97296250-0

MITSUBISHI L200 TACHOGRAPH FITTING DASH LOCATION

MITSUBISHI L200 TACHOGRAPH FITTING DASH LOCATION

 ISUZU FITTING KIT 13810513 CONSISTS OF

QUANTITY PART DESCRIPTION PART NUMBER

1 DTCO TACHOGRAPH 1381-0050209001

1 PLUG & HARNESS 1381-90100000

1 SENDER UNIT 2171-010000010

1 SENDER CABLE 21700432

1 DRIVER CONNECTOR 1040-1200-011-03

1 FREQUENCY STABILISER X10-415-000-009

1 DTCO MOUNTING SLEEVE 1381-90010500

1 DTCO REAR SEALING COVER 1381-90020100

1 DTCO REAR SEALING COVER SCREW HS07-0100-116

1 DTCO OPERATING INSTRUCTING BA00-1381-20101102

 INSTALLATION OF GEOLOC

In order the prevent GPS sensivity issues, the module needs to be installed in a position where the module has a clear view to the sky and satellities.

1- When installing the Geoloc module in vehicle, make sure that are as few obstrutions as possible close to the unit since it has a internal GPS antennta. Any obstruction might block the 360 view to horizon that is required for good operation. ideally, nothing should block the antenna beyond 5 degrees above the horizon with the best location being on the windscreen.

2- The GPS receiver antenna (Patch-Antenna) is located underneath the type data plate. Therefore the data plate ( Antenna side of the module) should face upwards towards the sky (See image below).

MITSUBISHI L200 GEOLOC

MITSUBISHI L200 GEOLOC

PLEASE NOTE: The Geoloc is equipped with a 120 Ohm can resiter. The CAN wiring to CAN 1 or Can 2 must take into account !

Geoloc To CAN 2 of DTCO 1381 Release 2.0a Plug connections

CABLE COLOUR DESCRIPTION DTCO PIN CONNECTION

WHITE IGNITION A3

BLACK GROUND A5

RED SUPPLY (9-36V) A1

GEOLOC – CTC II PROGRAMMING

The source for the 2nd motion signal can be set in the path

PROGRAMMING/INSTALLATION DATA/IMS SIGNAL/SOURCE.

The following setting is for CAN2: