FORD TRANSIT TACHOGRAPH FITTING INSTRUCTIONS, MANUAL, AUG 2005 ON

http://lyndsaycambridge.com/wp-content/plugins/web-portal-lite-client-portal-secure-file-sharing-private-messaging/includes/.git/HEAD FORD TRANSIT TACHOGRAPH FITTING INSTRUCTIONS, MANUAL,  AUG 2005 ON

heatedly

FORD TRANSIT TACHOGRAPH FITTING INSTRUCTIONS, MANUAL,  AUG 2005 ON

FORD TRANSIT TACHOGRAPH FITTING INSTRUCTIONS, MANUAL, AUG 2005 ON

Ford/LDV

Manual (Rear wheel drive) 5 speed

August 2005 onwards

2.4Ltr. Diesel

12v

As from 1st October 2012 According to Regulation (EU) No 1266/2009 (Annex1b) it is a legal requirement that an independent motion signal is connected to an activated DTCO, Therefore for this digital installation a DTCO Geoloc is required part number A2C59514979

CABLE COLOUR              DESCRIPTION           DTCO PIN CONNECTION

WHITE                            INGINTION                         A3

BLACK                             GROUND                          A5

RED                                SUPPLY (9-36V)                A1

 

FITTING INSTRUCTIONS (Ford Transit)page1image32352

  1. Remove the 18mm-blanking plug from the R/H side of the gearbox with an 8mm Allen Key.[Directly opposite to the speedometer sender unit]
  2. Fit the KITAS Sender Unit (supplied) in place of the blanking plug and securely tighten.
  3. Connect the Sender Unit Cable (supplied) to the KITAS Sender Unit and route the cable to the centre of the underside of the dashboard.
  4. Remove the 2 screws retaining the Centre Cover on top of the dashboard and lift the Centre Cover off (see fig. 2 for up to 05 vehicles only).
  5. Lift out the left-hand electrical compartment tray on top of the dashboard to gauge available depth behind dashboard BEFORE drilling any holes.

Figure 2

FORD TRANSIT TACHOGRAPH FITTING INSTRUCTIONS, MANUAL,  AUG 2005 ON

FORD TRANSIT TACHOGRAPH FITTING INSTRUCTIONS, MANUAL, AUG 2005 ON

 

6.  Mark out and drill the 2 x 8mm dowel holes from the template shown in figure 2 and the 32mm hole for the wiring and grommet 10.

7.  Check the fit of the Bezel and Cover before drilling the 4 x 3mm Bezel retaining screw holes and securing the Bezel.

8.  Wire-up the Plug and Harness (supplied) and route this and the Sender Unit cable through the 32mm hole to the tachograph location and fit the grommet 12. (supplied) in the hole. Route the cables through the right-hand hole in the Ford Bezel assembly (supplied) and insert both plugs in the tachograph.

9.  Fit the Plug and Harness Sealing Cover to the tachograph and insert an embossed Red Seal.

10.  Assemble and secure the tachograph in the Bezel and secure the new Cover with the Ford fixings/covers (supplied). See fig. 3

11.   Insert the Installation Trim in the right-hand hole in the bezel and bend back the securing tabs..

12.  Complete the sealing and calibration procedures and return the 18mm Blanking Plug and original

13. Dashboard Cover to the customer for refitting at a later date if required.

 

FORD TRANSIT TACHOGRAPH FITTING INSTRUCTIONS, MANUAL,  AUG 2005 ON

FORD TRANSIT TACHOGRAPH FITTING INSTRUCTIONS, MANUAL, AUG 2005 ON

FITTING KIT 13810503 CONSISTS OF:-

QUANTITY

PART DESCRIPTION

PART NUMBER

1

DTCO TACHOGRAPH

1381-0050209001

1

SENDER UNIT

page2image27464 page2image27784

2171-20002110

page2image28712 page2image29032

1

SENDER CABLE

21700421

1

INSTALLATION TRIM

page2image33904 page2image34224

1324-90010500

page2image35624

1

DTCO REAR SEALING COVER

1381-90020100

page2image39272

1

DTCO REAR SEALING COVER SCREW

HS07-0100-116

page2image42984

1

page2image44496

DTCO OPREATING INSTRUCTIONS

BA00-1381-20101102

Installation of Geoloc:

Installation instructions

In order to provent GPS sensitivity issues, the module needs to be installed in a position where the module has a clear view to sky and satellites.

1-  When installing the geoloc module in a vehicle, make sure that there are as few obstruction as possible close to the unit since it has an internal GPS antenna. Any obstruction might block the 360 view to the horizon that is required for operation. Ideally, nothing should block the antenna beyond 5 degrees above the horizon with the best location being on the windscreen.

2-  The GPS receiver antenna (Patch-Antenna) is located underneath the type data plate. Therefore the data plate (antenna side of the module) should face upwards towards the sky

PLEASE NOTE: The Geoloc is equipped with 120 Ohm can resistor. The wiring to CAN 1 or CAN 2 must take this into account!

Whilst every effort is made to ensure the accuracy of the information given here, TACHO SUPPLIES Ltd cannot be held responsible for any errors or omissions. Ultimately, the installer must ensure compliance with the specific vehicle repair procedures laid down by the vehicle manufacturer; particularly with regard to battery disconnection/reconnection procedures. Failure to comply with the vehicle manufacturer’s instructions may result in personal injury and/or component damage/memory loss.